Solution For illegal Use, Will be Powered Off Soon, in All SPD Mobile Models
illegal use, will be powered off soon, This fault is mostly seen in SPD models. Mostly they are Spreedtrum SC6531 and its variants SC6531A, and SC6531E. There are two methods to repair it.
Method 1
1- Switch Off the mobile and take out the SIM cards.
2- Switch On the mobile again and go to the Setting
3- Go to Factory Default Or Factory Reset, or Wipe Data or Format option.
4- When you start factory Resetting, the mobile will ask you for the security code,
default codes for China mobiles are 1234, 0000,1122
After Resetting Default the mobile, usually your mobile's error will be removed.
You can use the mobile normally.
If not, then use Method 2.
Method 2
If you don't know the security code, you can not factory reset the mobile,
Sometimes, even after removing the SIM Card, the fault does not go away,
Then you will need method number 2
Method 2 is related to use of the tool so that we can reset or Formate the mobile
For Example:
I have SPD 6531E MOBILE Modle QQMEE Q11
Fault: Display " illegal use, will be powered off soon" and goes to power off immediately.
We will use the infinity box CM2SCR Module to repair the fault.
CM2SCR MODULE
HOW TO FORMAT VIA INFINITY BOX CM2SCR?
1- Select on upper bar 'SC65/77/89xx/SPD I FP'
2-In 'Setting ' CPU select 'SC6531E: REV: E000E: NOR: [4MB]'
drop-down box, respected CPU type, shown in the picture.
3-Press the button ' Formt FS' in exe.
4- Press the Boot key or use the Bootable cable.
5- Connect the mobile in power off condition via USB cable to the PC port
6-Remember, before processing, SPD UNISEC DRIVERS must be installed perfectly on your PC.
7-Before any work on mobile, please fully back up the flash file.
8- Wait until the end.
9- Disconnect the mobile and use it again.
How to read the Flash File?
1- Select on upper bar 'SC65/77/89xx/SPD I FP'
In 'Setting ' CPU select 'SC6531E: REV: E000E: NOR: [4MB]'
drop-down box, respected CPU type, shown in the 2ndd picture.
2-Press the 'Flash' button in the below drop-down box.
3-Press the ' Read Flash ' button.
4- Press the Boot key or use the Bootable cable.
5- Connect the mobile in power off condition(Brom Mode) via USB cable to the PC port
6-Remember, before processing, SPD UNISEC DRIVERS must be installed perfectly on your PC.
7-Before any work on mobile, please fully back up the flash file.
8- Wait until the end.
9- Disconnect the mobile and use it again.
READING LOGS,
Operation : Read Flash [ v1.06 ]
1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
BootSource : InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash : Control transfered!
Boot Done!
CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]
Read Flash Ok, Size : 4.00 MiB
Platform Version: MOCOR_16A.W17.43.4_Release
Project Version: SC6531EFM_BAR
HW Version: SC6531EFM_BAR
Saved to : C:\Users\Mughal\Desktop\QQMEE Q11\MOCOR_16A.W17.43.4_Release.bin
Done!
Elapsed: 00:01:34
Reconnect Power/Cable!
Disclaimer and precautions
There are many similar mobiles models in the market at present, Every mobile file is different from the other and the flash file is not compatible with each other
Before flashing backup your mobile's full firmware.
After the flash, paste the original IMEI numbers, never use the flash file IMEI numbers
I will be not responsible if your mobile dead or unfunctional by this file.
Please read the instructions carefully.
If You have any problem, please leave a comment.
Disclaimer
Only use the original imei numbers, which are found on the back side sticker of the mobile, or dial on the keypad *#06#
Gsm Solutions is not responsible for any illegal usage. All the information is only for educational purposes.
Posts
0 Comments